粘附式空氣干燥機

◆服務顯著特點 Product features

※擁有穩定性高共同的撒氣工作壓力和露點

1.粘附塔之高寬比與直徑經實驗報告成果精密五金求算，塔床壓力降小，要確保了縮小空氣潮濕劑5秒的接觸性時長，具備原材料氣的露點追求。

2.30％的干澡劑加工余量，用在應對干澡劑的自動氧化，確保干澡。

3.門頭傳播器，抓好氣團勻經由潮濕劑層，除掉溝流這種現象。

※粉碎氣量耗率不低于14％

1.優質的機筒定制，同步保存100％的物理吸附卡路里，處理的卡路里采用增長再造環節的再造氣濕度，提生產品的解吸力量，隨著再造更完全徹底。

2.吹干和復蘇選擇倒置形成對流措施，濕水汽流淌干的吸劑時效性果更佳。復蘇氣出口型含濕量調整在亞是處于飽和階段階段，使排氣閥門消音器器及排氣閥門路通道無結霜現象之慮。

3.可只能根據干澡機的啟用電機負載標準調控再造氣劑量，確定再造暖濕氣流間斷性不穩，再造水壓低至臨界狀態。

※潮濕劑采用年限長

1.應該的機筒盡寸，使氣體完成干澡劑層的水流量和時長堅持好的情形，寬裕切實發揮干澡劑的效能。

2.合情合理的軟件系統配值，在氣體流動開始機筒前，經除油除理盡快解決氣體流動中內含油率物與重危害物，制止空氣干燥劑層受危害。

※機器進行了先進高品質電動伸縮及氣動式閥和靠譜的全電子可編寫程序序的控制機，人機對戰操作界面團結，重新累計屏幕上顯示雙塔生產，再循環生長期現廠可編，出廠之添加10min。蝶閥使用年限歷時50萬次姿勢。

※筒身外壁作冷鍍鋅鐵防繡解決，10年不浮銹。

※性動作精確度、維持性維持、操作的操作簡單，使用不要根基。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆大部分高技術數據 Main technical parameters